ABS sheet extrusion molding process control points

ABS sheet extrusion molding process control points

  • 13/04/2019 08:12:03

ABS sheet extrusion molding process control points(1) Feeding. The material should be fed in time to ensure that the hopper is not empty, in order to prevent the air from directly entering the drying c…

Read more

Preparation process of ABS sheet

Preparation process of ABS sheet

  • 12/04/2019 08:55:30

Preparation process of ABS sheet(1) The raw material is dried. ABS pellets are extremely hygroscopic and must be used before use.Dry. Drying can use hot air circulation oven or hot air hopper type recl…

Read more

Add waste materials to ABS sheet

Add waste materials to ABS sheet

  • 11/04/2019 09:27:24

Add waste materials to ABS sheet1. Material selection and performanceABS is an amorphous polymer. Under the action of heat and external force, it enters the viscous flow state from the glass state at r…

Read more

Plate (sheet) material forming process

Plate (sheet) material forming process

  • 10/04/2019 08:54:56

Plate (sheet) material forming processThe plastics of the production board (sheet) are mainly soft polyvinyl chloride, hard polyvinyl chloride, polyethylene.Alkene, polyamide, polymethyl, polycarbonate…

Read more
Characteristics and uses of PTFE - Suspension PTFE

Characteristics and uses of PTFE - Suspension PTFE

  • 09/04/2019 08:40:25

Characteristics and uses of PTFEVariety: Suspension PTFEfeature:1. White waxy fine particle material;2. Poor strength;3. Self-lubricating, non-adhesive, stress cracking is good, dynamic and static coef…

Read more

Modification du polymère

Modification du polymère

  • 08/04/2019 10:13:08

Modification du polymreLa modification du polymre a un sens large et toute mthode pour amliorer les proprits du polymre peut tre appele modification, telle que des mthodes de modification telles que le…

Read more

Polymer modification

Polymer modification

  • 08/04/2019 10:12:37

Polymer modificationThe modification of the polymer is a broad meaning, and any method for improving the properties of the polymer can be referred to as modification, such as modification methods such …

Read more

Fluoroplastic

Fluoroplastic

  • 04/04/2019 09:20:54

FluoroplasticFluoroplastic refers to a class of plastics with fluorine atoms in the polymer backbone. It is obtained by homopolymerization or copolymerization of a fluorine-containing monomer, and is c…

Read more

Hot News

ABS sheet extrusion molding process control points

ABS sheet extrusion molding process control points

ABS sheet extrusion molding process control points(1) Feeding. The material should be fed in time to ensure that the hopper is not empty, in order to prevent the air from directly entering the drying cycle system, affecting the dry return air speed. Diffe

Preparation process of ABS sheet

Preparation process of ABS sheet

Preparation process of ABS sheet(1) The raw material is dried. ABS pellets are extremely hygroscopic and must be used before use.Dry. Drying can use hot air circulation oven or hot air hopper type reclaimed materialDryer. The drying process undergoes thre

Add waste materials to ABS sheet

Add waste materials to ABS sheet

Add waste materials to ABS sheet1. Material selection and performanceABS is an amorphous polymer. Under the action of heat and external force, it enters the viscous flow state from the glass state at room temperature through a high elastic state to form a

Plate (sheet) material forming process

Plate (sheet) material forming process

Plate (sheet) material forming processThe plastics of the production board (sheet) are mainly soft polyvinyl chloride, hard polyvinyl chloride, polyethylene.Alkene, polyamide, polymethyl, polycarbonate, cellulose acetate, etc., the first four varieties ar

Characteristics and uses of PTFE - Suspension PTFE

Characteristics and uses of PTFE - Suspension PTFE

Characteristics and uses of PTFEVariety: Suspension PTFEfeature:1. White waxy fine particle material;2. Poor strength;3. Self-lubricating, non-adhesive, stress cracking is good, dynamic and static coefficient is the lowest among plastics;4. Excellent resi

Tags