Cast film mechanical winding device

                                            Cast film mechanical winding device

    Corona treatment device: cast film after corona treatment, can improve the surface tension of the film to improve the printing of the film and together with other materials a force, thereby increasing the film printing fastness of the peel strength of the composite material. The surface tension of the treated film is required to reach 32-58 mN / m, usually between 38-44 mN / m. It should be noted that corona-treated films are not good for soldering. Corona treatment will lead. 1 a corona treatment roller; 2 a film; 3 a discharge electrode; 4 a corona. The temperature of the film from the processor is increased, so cooling is to be strengthened before the film is taken up.
    Winding device: The film adopts the initiative winding (shaft center coiling) form, in order to adapt to the casting film width and high production line speed characteristics, winding devices are generally automatic or semi-automatic cutting, changing the volume. Automatic double-roll change applications more. Single roller automatic roll change sometimes have applications. The film roll is usually 300-800 mm in diameter.
    The film winding device also includes a film cutting device. Film cutting methods are generally: electric cutting method and blade cutting method. Electrothermal cutting method is the use of electric wire heat the film blown blade cutting method has artificial cutting and mechanical cutting, mechanical cutting is the use of compressed air to promote the cutting blade along the film to move quickly to complete the transverse direction. Since the film is continuously moved in the winding direction, the shape of the end of the film after cutting is beveled. Cut the film while blowing the wind, so that cut the film close to the new mandrel roll start winding. Film winding is the key to control tension, tension is too large or too small will affect the quality of the film. The general winding device has a tension adjustment mechanism, the film winding tension control at 100 ~ 200 N, the use of torque motor to ensure a constant winding tension.
    Other ancillary equipment: casting molding equipment, in addition to the above-mentioned device, as well as flattening roll, roll guide roller and so on. Roller is to prevent roll wrinkles when rolling the film. Roller is to prevent roll wrinkles when rolling the film. Flattening roller flattened roller with herringbone, curved roller and so on. Herringbone flat roll roller surface with left and right groove. The curved roller is a roller whose axis is curved into an arc shape. During the rotation, the arched side always faces the film, and the roller camber angle is about 15 ° -30 °.

  • 19/12/2017
  • Recently
Click here to view Previous or Next

Related News

Cost-effective industrial laminate

Cost-effective industrial laminate

  • 13/02/2019 09:10:01

The cheapest industrial laminates (Class X) are used in large quantities where the dielectric properties are less important. It is made from unbleached kraft paper and about 30% phenolic resin. It has …

Read more

Casting PA film and production technology

Casting PA film and production technology

  • 21/12/2017 09:33:12

Casting PA film and production technology 1. Casting PA film and its raw materials used: PA film has the advantages of high strength, good toughness, good transparency, good heat resistance and cold…

Read more

Downstream production line auxiliaries

Downstream production line auxiliaries

  • 18/12/2017 09:42:18

Downstream production line auxiliaries Thickness measurement device: In the high-speed continuous production process, cast film thickness measurement must be non-contact automatic tracking. Most o…

Read more

Casting film production line in the cooling device

Casting film production line in the cooling device

  • 15/12/2017 10:03:16

Casting film production line in the cooling device Casting production line in the cooling device mainly by the rack, cooling roller, peel roller, refrigeration system and air knife, auxiliary device…

Read more

Hot News

Film composite technology

Film composite technology

Film composite technologyMulti-layer composite film or film and aluminum foil, paper multi-layer composite material, in terms of air barrier properties, heat sealability, printability, peel strength, hygiene and economic rationality, there is a significan

Calendered film and hard sheet

Calendered film and hard sheet

Calendered film and hard sheetCalendering is a method in which a thermoplastic film of two or more phases is compression molded between rotating rolls to produce a continuous film or sheet.In the field of plastic processing, the extrusion method is the ma

Extrusion theory and characteristics of extrusion

Extrusion theory and characteristics of extrusion

The flow theory of plastics in the extrusion process: The modern ordinary extrusion theory is based on the three basic functions of solid transportation, melting and melt transportation. Thus, a conventional screw includes three functional segments: a sol

Thermoforming of plastics

Thermoforming of plastics

Thermoforming of plasticsThermoforming is a method of making plastic articles using sheets of thermoplastics as a raw material. When manufacturing, the sheet cut into a certain size and a fixed shape is first clamped on the frame and heated to a thermoela

The general principle of blow molding

The general principle of blow molding

The general principle of blow molding can be summarized as the blowing of compressed air into a molten parison, which is laterally inflated, pressed against the sub-mold type control surface, and cooled to form a hollow product. Therefore, blow molding ge

Tags