Aluminum plastic composite board process

                          Aluminum plastic composite board process

    Aluminium coils are anodized, rolled with a primer, high temperature paint, cooled, roll painted, high temperature baked, cooled, coiled to form a painted aluminum coil. Then sanding, leveling, brown brush cleaning, double-sided coating (or double-sided adhesive film), three-layer composite (plastic plate, under-laminated aluminum sheet), cut-to-length cutting, cold pressing Leveling, trimming, lengthening and sticking the protective film into aluminum-plastic composite boards. Aluminium plastic plates can be produced either continuously or intermittently. In continuous production, the coating of aluminum sheet, the composite of aluminum sheet and plastic core, and the extrusion of the core sheet are performed at the same time. Intermittent production is the first production of plastic sheeting, followed by adhesion of the coated aluminum sheet with a calender roll mill, or a layered composite.
The continuous production process of aluminum-plastic composite board is shown below: Resin-Extrusion-Plastic Board-Sanding-Brown Brush-Double Side Coating; Aluminum Roll-Oxidation-Primer Roll-Paint-Paint Roll-Paint Three-layer compound-drying-cooling flattening-protecting film-cutting length-finished product
    The performance of the aluminum-plastic composite board is in accordance with the ASTM MD 117-3359 standard. Aluminum-plastic composite board has just started in China and is in the development stage. With its unique performance, it meets the requirements of modern architecture and has broad market potential.
    Other extruded composite products: Non-plastic profiled composites and non-plastics (mainly metal) profiled composites made of different profiles, the main characteristics are large rigidity, good dimensional stability. By embedding the metal in the profile, this profile can be used as a structural material and can withstand loads for long periods without pillars; this profile also eliminates thermal expansion and contraction in the plastic.

  • 10/05/2018
  • Recently
Click here to view Previous or Next

Related News

Casting PA film and production technology

Casting PA film and production technology

  • 21/12/2017 09:33:12

Casting PA film and production technology 1. Casting PA film and its raw materials used: PA film has the advantages of high strength, good toughness, good transparency, good heat resistance and cold…

Read more

Cast film mechanical winding device

Cast film mechanical winding device

  • 19/12/2017 09:21:48

Cast film mechanical winding device Corona treatment device: cast film after corona treatment, can improve the surface tension of the film to improve the printing of the film and together with other…

Read more

Downstream production line auxiliaries

Downstream production line auxiliaries

  • 18/12/2017 09:42:18

Downstream production line auxiliaries Thickness measurement device: In the high-speed continuous production process, cast film thickness measurement must be non-contact automatic tracking. Most o…

Read more

Casting film production line in the cooling device

Casting film production line in the cooling device

  • 15/12/2017 10:03:16

Casting film production line in the cooling device Casting production line in the cooling device mainly by the rack, cooling roller, peel roller, refrigeration system and air knife, auxiliary device…

Read more

Hot News

Coextrusion

Coextrusion

Coextrusion enhances the process of extrusion coating and lamination. Prior to single-pass coextrusion, the use of a sandwich resin structure required multiple passes or multiple coaters from a single coater. Coextrusion is used to reinforce recyclable wa

Seam extruder die _2

Seam extruder die _2

The final forming section or lip must be adjustable with the resin transverse thickness control of the die. This can be achieved by moving one lip to move the other lip. This movement can also be made by means of a large-diameter hard-form lip (hard-forme

Seam extrusion die _1

Seam extrusion die _1

When a single extruder is used, the resin typically enters the population mold from the needle valve through a 25-37 mm diameter drop tube. The die must distribute the material throughout the exit width to form a suitable thickness and a smooth surface. T

Valve device for extruder

Valve device for extruder

After passing through the web (but in front of the die), it is preferred to have a polymer pressure limiting device to vary the total outlet pressure required for good mixing within the screw, and the possibility of using a fixed orifice is small. The mos

Mesh filter for extruder

Mesh filter for extruder

The resin is filtered after leaving the barrel and screw area to ensure that a clean polymer is applied to the web. The filter also reduces infusibles such as fish eyes and gels in the polymer melt stream. The most common type of filtration in coating/com

Tags